http://taigownersclub.forumotion.net/taig-manual-mill-f7/-t1.htm Wed, 22 Jul 2009 01:32:22 GMT 10 http://i63.servimg.com/u/f63/13/33/05/12/toc_lo17.jpg http://taigownersclub.forumotion.net/taig-manual-mill-f7/-t1.htm http://taigownersclub.forumotion.net/taig-manual-mill-f7/a2z-end-mill-holders-t315.htm rkernell
I was facing a block of 6061, making cuts of 2.5 mil using a 3/8 roughing end mil, at the lowest spindle speed. The chatter was slight but it left noticeable marks on the material. I changed to the 3/8 ER16 collet and the problem did not re-occur. The cuts were much cleaner as well.

Rick]]> Taig Manual Mill Wed, 22 Jul 2009 01:32:22 GMT http://taigownersclub.forumotion.net/taig-manual-mill-f7/a2z-end-mill-holders-t315.htm#1910 http://taigownersclub.forumotion.net/taig-manual-mill-f7/a2z-end-mill-holders-t315.htm http://taigownersclub.forumotion.net/taig-manual-mill-f7/metric-collets-t280.htm Countryman
Does anybody sell metric collets for the non ER mill spindle? Using the 0.001" over and 0.004 under rule on the Taig site nominal metric sizes (4, 5 & 6mm etc.) fit nicely between the imperial collets!

Cheers,]]> Taig Manual Mill Fri, 22 May 2009 16:32:06 GMT http://taigownersclub.forumotion.net/taig-manual-mill-f7/metric-collets-t280.htm#1603 http://taigownersclub.forumotion.net/taig-manual-mill-f7/metric-collets-t280.htm http://taigownersclub.forumotion.net/taig-manual-mill-f7/x-axis-tilt-t273.htm rkernell I have found that the X axis carriage on my 2019 has a 0.006 inch tilt with the front portion of the table high. I looked through the sites to see if there was an adjustment to clean this up, but wasn't able to find one. Has anyone else found this and how did you adjust it out? Taig Manual Mill Sun, 19 Apr 2009 03:01:08 GMT http://taigownersclub.forumotion.net/taig-manual-mill-f7/x-axis-tilt-t273.htm#1529 http://taigownersclub.forumotion.net/taig-manual-mill-f7/x-axis-tilt-t273.htm http://taigownersclub.forumotion.net/taig-manual-mill-f7/dro-t180.htm thumper Hello, I have a 2019cr mill no cnc yet. Has anyone put a DRO on there mill? Looking for even some ideas on mounting chinese scales to mill. Any links to someone that has would be helpfull. I love this mill so much more handy than the mill drill I also have.Thank You Steve Taig Manual Mill Sat, 07 Feb 2009 04:57:19 GMT http://taigownersclub.forumotion.net/taig-manual-mill-f7/dro-t180.htm#933 http://taigownersclub.forumotion.net/taig-manual-mill-f7/dro-t180.htm http://taigownersclub.forumotion.net/taig-manual-mill-f7/taig-mill-accessories-t226.htm rkernell I have ordered a 2019 CNC ready mill, but I plan on using in the manual configuration to learn milling. The sales person is putting together a package of starter equipment for me. What are the tools and accessories that I should start getting to have in my inventory? I think that a rotary table would be extremely helpful, but that might be my inexperience. Taig Manual Mill Fri, 13 Mar 2009 07:24:59 GMT http://taigownersclub.forumotion.net/taig-manual-mill-f7/taig-mill-accessories-t226.htm#1264 http://taigownersclub.forumotion.net/taig-manual-mill-f7/taig-mill-accessories-t226.htm